{"id":15829,"date":"2026-11-20T10:35:00","date_gmt":"2026-11-20T09:35:00","guid":{"rendered":"https:\/\/www.lukaswojcik.com\/blog\/?p=15829"},"modified":"2026-11-14T23:38:46","modified_gmt":"2026-11-14T22:38:46","slug":"sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays","status":"publish","type":"post","link":"https:\/\/www.lukaswojcik.com\/blog\/en\/cctv\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\/","title":{"rendered":"Sending Camera Motion Alerts to Home Assistant: Understanding ONVIF Delays"},"content":{"rendered":"<p>ONVIF events can deliver motion alerts to Home Assistant faster than checking a state at fixed intervals. The advantage comes from an already waiting Pull-Point request or a camera notification sent to a webhook. Detection, network transport and processing still take time. Neither delay-free nor loss-free delivery is guaranteed.<\/p>\n<p>The implementation details below refer to Home Assistant Core 2026.10.4 and its <code>onvif-zeep-async 4.3.0<\/code> dependency. The protocol explanation follows ONVIF Core Specification 26.06.<\/p>\n<h2>Pull-Point: a request that waits<\/h2>\n<p><code>CreatePullPointSubscription<\/code> requests a subscription and returns an endpoint. <code>PullMessages<\/code> then retrieves available notifications. If messages are already queued, the camera responds immediately up to the requested message limit. Otherwise the request waits for an event or the timeout. This is long polling, not operation without requests.<\/p>\n<p>With Basic Notification, <code>Subscribe<\/code> instead registers a receiving address. The camera opens a connection to that address and delivers <code>Notify<\/code> messages. Home Assistant uses a webhook for this purpose: a receiving URL to which the camera sends its notifications. Subscription lifetime and renewal matter for both methods; actual support and reliability depend on the device.<\/p>\n<h2>What a five-second interval means<\/h2>\n<p>For an interface that reports only the current alarm state, almost a full interval can pass after detection before the next check. A five-second interval therefore adds up to approximately five seconds of waiting. A short alarm between checks can be missed unless the interface retains alarm states or provides an event history.<\/p>\n<p>The familiar half-interval average assumes events distributed uniformly across the interval and checks that run regularly. Under those assumptions, a five-second interval adds an average 2.5 seconds. This is a calculation, not an end-to-end latency measurement: detection, transport, queues and automation processing add further time.<\/p>\n<h2>What Home Assistant actually does<\/h2>\n<p>The inspected integration first tries Pull-Point. With the default \u201cEnable Webhooks\u201d option active, it also attempts a webhook. A successfully processed webhook notification pauses Pull-Point retrieval. Pull-Point renewals are paused as well, allowing the old subscription to expire. A continuously active parallel receiving path is therefore not guaranteed.<\/p>\n<p>Pull-Point requests specify a 60-second timeout and a limit of 100 messages. The integration normally waits 0.75 seconds between requests. Some failures cause longer retry delays. Events during those gaps need a later request; a waiting request does not remove every source of delay.<\/p>\n<p>The requested subscription lifetime is ten minutes. However, the library schedules renewal at 80 percent of the lifetime reported by the camera, falling back to the requested duration when timing information is absent. Eight minutes therefore fits a ten-minute grant but is not a universal interval for all cameras. The calculation applies a minimum lifetime of 60 seconds before multiplying by 0.8; unusually short grants therefore need particular attention.<\/p>\n<figure class=\"lw-diagram\"><img decoding=\"async\" src=\"https:\/\/lukaswojcik.com\/blog\/wp-content\/uploads\/diagrams\/onvif-reviewed-15829-en-20261025.png?v=20261114\" alt=\"ONVIF event delivery: fixed polling, Pull-Point, webhook and renewal limits.\" loading=\"lazy\"><figcaption>ONVIF event delivery: fixed polling, Pull-Point, webhook and renewal limits.<\/figcaption><\/figure>\n<h2>Network paths and outages<\/h2>\n<p>Pull-Point starts with a connection from Home Assistant to the camera&#8217;s ONVIF endpoint. A stateful firewall must permit the associated replies. The event transport itself does not require internet access. Webhooks additionally need a reachable path from the camera to the actual registered Home Assistant address and port.<\/p>\n<p>A webhook blocked from the beginning can remain unnoticed while working Pull-Point continues. A later silent failure after switching to the webhook is harder to detect. Successful subscription renewal does not prove that notifications reach the receiver. Test motion and actual sensor changes therefore matter. A blocked reverse path cannot be described as guaranteeing no event loss.<\/p>\n<p>Firewall, proxy and router idle limits should accommodate the 60-second Pull-Point timeout with sufficient margin. A value barely above 60 seconds alone does not guarantee uninterrupted operation.<\/p>\n<h2>Diagnosing faults before blaming firmware<\/h2>\n<p>HTTP 500 can carry a normal SOAP fault response. The fault content and operation matter. Initial checks include ONVIF permissions, camera time, enabled detection, supported topics, endpoint addresses and network paths. Subscription limits, renewal failures and firmware version follow.<\/p>\n<p>The integration and library handle various failures through retries or new subscriptions. Many messages appear at debug level; unknown or unparseable events can also generate warnings. Logs narrow down causes but do not alone prove a device defect. An NVR performing its own detection on an RTSP stream is a possible alternative architecture, requiring suitable software and computing resources.<\/p>\n<h2>Testing automations meaningfully<\/h2>\n<p>Known event types that actually arrive can create suitable Home Assistant entities, such as motion binary sensors. The camera must detect the event, and Home Assistant must map the reported event category to the appropriate sensor. A useful test covers alarm onset, alarm clearing, restart and a deliberately interrupted connection. Restored connectivity should again produce observable state changes.<\/p>\n<div class=\"lw-faq\">\n<h2>Questions and answers<\/h2>\n<h3>How many requests occur without events?<\/h3>\n<p>An idealised Pull-Point cycle with a 60-second wait and a 0.75-second pause yields about 59 retrieval requests per hour over time. A granted ten-minute lifetime adds about 7.5 renewals, for roughly 67 requests. Setup, synchronisation, events, other Home Assistant requests and retries are excluded. Fixed polling produces 720 requests per hour at five-second intervals and 3,600 at one-second intervals.<\/p>\n<h3>Does a failed subscription switch to fixed state polling?<\/h3>\n<p>The inspected event manager has no such replacement. Retries and possible switches between webhook and Pull-Point remain part of event processing. Unsupported or lost events are not automatically reconstructed.<\/p>\n<h3>How can Pull-Point be tested specifically?<\/h3>\n<p>Disabling \u201cEnable Webhooks\u201d makes the integration try Pull-Point, provided the device actually supplies that service. Testing should cover real state changes and behaviour after an interruption.<\/p>\n<\/div>\n<div class=\"lw-quellen\">\n<h2>Sources<\/h2>\n<ul>\n<li><a href=\"https:\/\/www.onvif.org\/specs\/core\/ONVIF-Core-Specification.pdf\" rel=\"noopener noreferrer\" target=\"_blank\">ONVIF Core Specification 26.06, section 9<\/a><\/li>\n<li><a href=\"https:\/\/www.home-assistant.io\/integrations\/onvif\/\" rel=\"noopener noreferrer\" target=\"_blank\">Home Assistant: ONVIF<\/a><\/li>\n<li><a href=\"https:\/\/github.com\/home-assistant\/core\/blob\/2026.10.4\/homeassistant\/components\/onvif\/event_manager.py\" rel=\"noopener noreferrer\" target=\"_blank\">Home Assistant 2026.10.4: event manager<\/a><\/li>\n<li><a href=\"https:\/\/pypi.org\/project\/onvif-zeep-async\/4.3.0\/\" rel=\"noopener noreferrer\" target=\"_blank\">onvif-zeep-async 4.3.0<\/a><\/li>\n<\/ul>\n<\/div>\n","protected":false},"excerpt":{"rendered":"<p>Pull-Point and webhooks can reduce the extra waiting caused by fixed state polling. Home Assistant 2026.10.4 still has request gaps and subscription limits; successful renewal does not prove that notifications arrive.<\/p>\n","protected":false},"author":1,"featured_media":32509,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[7],"tags":[91106,91398,91365,91626],"class_list":["post-15829","post","type-post","status-publish","format-standard","hentry","category-cctv","tag-automation","tag-monitoring-cctv-pl","tag-home-assistant","tag-smart-home-de"],"yoast_head":"<!-- This site is optimized with the Yoast SEO plugin v28.1 - https:\/\/yoast.com\/product\/yoast-seo-wordpress\/ -->\n<title>Sending Camera Motion Alerts to Home Assistant: Understanding ONVIF Delays | Lukas Wojcik<\/title>\n<meta name=\"description\" content=\"How a pull-point subscription differs from polling, what renewing it costs, and why a missed renewal looks exactly like a camera without motion.\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/www.lukaswojcik.com\/blog\/en\/cctv\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\/\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Sending Camera Motion Alerts to Home Assistant: Understanding ONVIF Delays | Lukas Wojcik\" \/>\n<meta property=\"og:description\" content=\"How a pull-point subscription differs from polling, what renewing it costs, and why a missed renewal looks exactly like a camera without motion.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/www.lukaswojcik.com\/blog\/en\/cctv\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\/\" \/>\n<meta property=\"og:site_name\" content=\"Lukas Wojcik - Blog\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-20T09:35:00+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/www.lukaswojcik.com\/blog\/wp-content\/uploads\/2026\/11\/flux-voll2-15829-15829.png\" \/>\n\t<meta property=\"og:image:width\" content=\"1200\" \/>\n\t<meta property=\"og:image:height\" content=\"630\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/png\" \/>\n<meta name=\"author\" content=\"Lukas Wojcik\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"Lukas Wojcik\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"4 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\\\/\\\/schema.org\",\"@graph\":[{\"@type\":\"Article\",\"@id\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/en\\\/cctv\\\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\\\/#article\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/en\\\/cctv\\\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\\\/\"},\"author\":{\"name\":\"Lukas Wojcik\",\"@id\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/#\\\/schema\\\/person\\\/895f7604f9b6b71aad9bba33af28d0f9\"},\"headline\":\"Sending Camera Motion Alerts to Home Assistant: Understanding ONVIF Delays\",\"datePublished\":\"2026-11-20T09:35:00+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/en\\\/cctv\\\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\\\/\"},\"wordCount\":898,\"commentCount\":0,\"publisher\":{\"@id\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/#\\\/schema\\\/person\\\/895f7604f9b6b71aad9bba33af28d0f9\"},\"image\":{\"@id\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/en\\\/cctv\\\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/flux-voll2-15829-15829.png\",\"keywords\":[\"Automation\",\"CCTV\",\"Home Assistant\",\"Smart Home\"],\"articleSection\":[\"CCTV\"],\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/en\\\/cctv\\\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\\\/#respond\"]}]},{\"@type\":\"WebPage\",\"@id\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/en\\\/cctv\\\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\\\/\",\"url\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/en\\\/cctv\\\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\\\/\",\"name\":\"Sending Camera Motion Alerts to Home Assistant: Understanding ONVIF Delays | Lukas Wojcik\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/en\\\/cctv\\\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\\\/#primaryimage\"},\"image\":{\"@id\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/en\\\/cctv\\\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/flux-voll2-15829-15829.png\",\"datePublished\":\"2026-11-20T09:35:00+00:00\",\"description\":\"How a pull-point subscription differs from polling, what renewing it costs, and why a missed renewal looks exactly like a camera without motion.\",\"breadcrumb\":{\"@id\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/en\\\/cctv\\\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\\\/#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/en\\\/cctv\\\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\\\/\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/en\\\/cctv\\\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\\\/#primaryimage\",\"url\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/flux-voll2-15829-15829.png\",\"contentUrl\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/flux-voll2-15829-15829.png\",\"width\":1200,\"height\":630,\"caption\":\"Sending Camera Motion Alerts to Home Assistant: Understanding ONVIF Delays\"},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/en\\\/cctv\\\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\\\/#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/de\\\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Sending Camera Motion Alerts to Home Assistant: Understanding ONVIF Delays\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/#website\",\"url\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/\",\"name\":\"Lukas Wojcik - Blog\",\"description\":\"\",\"publisher\":{\"@id\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/#\\\/schema\\\/person\\\/895f7604f9b6b71aad9bba33af28d0f9\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"en-US\"},{\"@type\":[\"Person\",\"Organization\"],\"@id\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/#\\\/schema\\\/person\\\/895f7604f9b6b71aad9bba33af28d0f9\",\"name\":\"Lukas Wojcik\",\"image\":{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/wp-content\\\/uploads\\\/2026\\\/07\\\/lw-x2.jpg\",\"url\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/wp-content\\\/uploads\\\/2026\\\/07\\\/lw-x2.jpg\",\"contentUrl\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/wp-content\\\/uploads\\\/2026\\\/07\\\/lw-x2.jpg\",\"width\":424,\"height\":636,\"caption\":\"Lukas Wojcik\"},\"logo\":{\"@id\":\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\\\/wp-content\\\/uploads\\\/2026\\\/07\\\/lw-x2.jpg\"},\"sameAs\":[\"https:\\\/\\\/www.lukaswojcik.com\\\/blog\"]}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"Sending Camera Motion Alerts to Home Assistant: Understanding ONVIF Delays | Lukas Wojcik","description":"How a pull-point subscription differs from polling, what renewing it costs, and why a missed renewal looks exactly like a camera without motion.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/www.lukaswojcik.com\/blog\/en\/cctv\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\/","og_locale":"en_US","og_type":"article","og_title":"Sending Camera Motion Alerts to Home Assistant: Understanding ONVIF Delays | Lukas Wojcik","og_description":"How a pull-point subscription differs from polling, what renewing it costs, and why a missed renewal looks exactly like a camera without motion.","og_url":"https:\/\/www.lukaswojcik.com\/blog\/en\/cctv\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\/","og_site_name":"Lukas Wojcik - Blog","article_published_time":"2026-11-20T09:35:00+00:00","og_image":[{"width":1200,"height":630,"url":"https:\/\/www.lukaswojcik.com\/blog\/wp-content\/uploads\/2026\/11\/flux-voll2-15829-15829.png","type":"image\/png"}],"author":"Lukas Wojcik","twitter_card":"summary_large_image","twitter_misc":{"Written by":"Lukas Wojcik","Est. reading time":"4 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"Article","@id":"https:\/\/www.lukaswojcik.com\/blog\/en\/cctv\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\/#article","isPartOf":{"@id":"https:\/\/www.lukaswojcik.com\/blog\/en\/cctv\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\/"},"author":{"name":"Lukas Wojcik","@id":"https:\/\/www.lukaswojcik.com\/blog\/#\/schema\/person\/895f7604f9b6b71aad9bba33af28d0f9"},"headline":"Sending Camera Motion Alerts to Home Assistant: Understanding ONVIF Delays","datePublished":"2026-11-20T09:35:00+00:00","mainEntityOfPage":{"@id":"https:\/\/www.lukaswojcik.com\/blog\/en\/cctv\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\/"},"wordCount":898,"commentCount":0,"publisher":{"@id":"https:\/\/www.lukaswojcik.com\/blog\/#\/schema\/person\/895f7604f9b6b71aad9bba33af28d0f9"},"image":{"@id":"https:\/\/www.lukaswojcik.com\/blog\/en\/cctv\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\/#primaryimage"},"thumbnailUrl":"https:\/\/www.lukaswojcik.com\/blog\/wp-content\/uploads\/2026\/11\/flux-voll2-15829-15829.png","keywords":["Automation","CCTV","Home Assistant","Smart Home"],"articleSection":["CCTV"],"inLanguage":"en-US","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/www.lukaswojcik.com\/blog\/en\/cctv\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\/#respond"]}]},{"@type":"WebPage","@id":"https:\/\/www.lukaswojcik.com\/blog\/en\/cctv\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\/","url":"https:\/\/www.lukaswojcik.com\/blog\/en\/cctv\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\/","name":"Sending Camera Motion Alerts to Home Assistant: Understanding ONVIF Delays | Lukas Wojcik","isPartOf":{"@id":"https:\/\/www.lukaswojcik.com\/blog\/#website"},"primaryImageOfPage":{"@id":"https:\/\/www.lukaswojcik.com\/blog\/en\/cctv\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\/#primaryimage"},"image":{"@id":"https:\/\/www.lukaswojcik.com\/blog\/en\/cctv\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\/#primaryimage"},"thumbnailUrl":"https:\/\/www.lukaswojcik.com\/blog\/wp-content\/uploads\/2026\/11\/flux-voll2-15829-15829.png","datePublished":"2026-11-20T09:35:00+00:00","description":"How a pull-point subscription differs from polling, what renewing it costs, and why a missed renewal looks exactly like a camera without motion.","breadcrumb":{"@id":"https:\/\/www.lukaswojcik.com\/blog\/en\/cctv\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\/#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/www.lukaswojcik.com\/blog\/en\/cctv\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\/"]}]},{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/www.lukaswojcik.com\/blog\/en\/cctv\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\/#primaryimage","url":"https:\/\/www.lukaswojcik.com\/blog\/wp-content\/uploads\/2026\/11\/flux-voll2-15829-15829.png","contentUrl":"https:\/\/www.lukaswojcik.com\/blog\/wp-content\/uploads\/2026\/11\/flux-voll2-15829-15829.png","width":1200,"height":630,"caption":"Sending Camera Motion Alerts to Home Assistant: Understanding ONVIF Delays"},{"@type":"BreadcrumbList","@id":"https:\/\/www.lukaswojcik.com\/blog\/en\/cctv\/sending-camera-motion-alerts-to-home-assistant-understanding-onvif-delays\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/www.lukaswojcik.com\/blog\/de\/"},{"@type":"ListItem","position":2,"name":"Sending Camera Motion Alerts to Home Assistant: Understanding ONVIF Delays"}]},{"@type":"WebSite","@id":"https:\/\/www.lukaswojcik.com\/blog\/#website","url":"https:\/\/www.lukaswojcik.com\/blog\/","name":"Lukas Wojcik - Blog","description":"","publisher":{"@id":"https:\/\/www.lukaswojcik.com\/blog\/#\/schema\/person\/895f7604f9b6b71aad9bba33af28d0f9"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/www.lukaswojcik.com\/blog\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"en-US"},{"@type":["Person","Organization"],"@id":"https:\/\/www.lukaswojcik.com\/blog\/#\/schema\/person\/895f7604f9b6b71aad9bba33af28d0f9","name":"Lukas Wojcik","image":{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/www.lukaswojcik.com\/blog\/wp-content\/uploads\/2026\/07\/lw-x2.jpg","url":"https:\/\/www.lukaswojcik.com\/blog\/wp-content\/uploads\/2026\/07\/lw-x2.jpg","contentUrl":"https:\/\/www.lukaswojcik.com\/blog\/wp-content\/uploads\/2026\/07\/lw-x2.jpg","width":424,"height":636,"caption":"Lukas Wojcik"},"logo":{"@id":"https:\/\/www.lukaswojcik.com\/blog\/wp-content\/uploads\/2026\/07\/lw-x2.jpg"},"sameAs":["https:\/\/www.lukaswojcik.com\/blog"]}]}},"_links":{"self":[{"href":"https:\/\/www.lukaswojcik.com\/blog\/wp-json\/wp\/v2\/posts\/15829","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.lukaswojcik.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.lukaswojcik.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.lukaswojcik.com\/blog\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.lukaswojcik.com\/blog\/wp-json\/wp\/v2\/comments?post=15829"}],"version-history":[{"count":10,"href":"https:\/\/www.lukaswojcik.com\/blog\/wp-json\/wp\/v2\/posts\/15829\/revisions"}],"predecessor-version":[{"id":34005,"href":"https:\/\/www.lukaswojcik.com\/blog\/wp-json\/wp\/v2\/posts\/15829\/revisions\/34005"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.lukaswojcik.com\/blog\/wp-json\/wp\/v2\/media\/32509"}],"wp:attachment":[{"href":"https:\/\/www.lukaswojcik.com\/blog\/wp-json\/wp\/v2\/media?parent=15829"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.lukaswojcik.com\/blog\/wp-json\/wp\/v2\/categories?post=15829"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.lukaswojcik.com\/blog\/wp-json\/wp\/v2\/tags?post=15829"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}